It is currently 28 Mar 2024, 16:28

Table Saw

Here's the place to talk about all your table saws, bandsaws, routers and dust extractors. In fact anything that makes noise and uses electrickery.

Re: Table Saw

Postby Tusses » 23 Jan 2017, 16:32

nice result :-)
and good that you are straight into using it :D
Tusses
Old Oak
 
Posts: 1300
Joined: 08 May 2016, 10:48
Location: in the middle of the middle
Name:

Re: Table Saw

Postby Andyp » 23 Jan 2017, 16:41

Well done Erich
I do not think therefore I do not am.

cheers
Andy
User avatar
Andyp
Petrified Pine
 
Posts: 11716
Joined: 22 Jul 2014, 07:05
Location: 14860 Normandy, France
Name: Andy

Re: Table Saw

Postby Commander » 23 Jan 2017, 19:07

Thanks for the kind words gents, I have to say I'm very pleased with it so far, makes a huge difference to the work shop, I should have done this a long time ago...
Commander
Sapling
 
Posts: 471
Joined: 29 Apr 2015, 15:11
Location: Pretoria, RSA
Name: Erich

Re: Table Saw

Postby Commander » 31 Jan 2017, 06:37

I have been meaning to do a quick wright-up about using vinegar to clean up rust, so here it is eventually!

Here are some before pics:

Image

Image

Image

Image

Even the wooden handle looks worse for ware:

Image

My first challenge was finding a container big enough to put the plane in, I eventually settled on a paint tray. The vinegar was diluted to about 50/50 with normal tap water, however I didn't measure this actually, it was more of an eye ball measurement. I started off with brushing the solution on with an old toothbrush and that actually worked pretty well right off the bat, however that is still a lot of work, so I wanted to soak the plane and see what would happen.

The plane soaked for about 3 days (I probably should have taken it out a little sooner, but things were just too busy to get round to it).

Image

As you can see I still didn't manage to submerge the whole plane, I did however manage to soak the parts. The solution was very dark and there was some foam on top showing me a chemical reaction as definitely taking place.

After taking it out of the solution it did still require a lot of brushing though...

Image

Image
But with some brushing the change was very apparent!

Image

I then started with "tool-in-a-can" and some fine water paper to clean up the residue and remaining rust. It did also seem necessary as the plane started to rust up again within minutes.

Image
Here you can see the difference between the 2 blades, one cleaned with tool-in-a-can and sanding only (in the plane) and one first cleaned with the vinegar method and finished with tool-in-a-can (in my hand). It did however for some reason leave the change in colour as can be seen just below the slot, I suspect this might be where the blade was hardened. It did seem to remove the outer finish of the blade as well, so I'm not sure if it will retain an edge as well as before.

Here is the final side by side comparison, the small plane was cleaned with tool-in-a-can only while the larger plane was done with vinegar.

Image

The results look similar but I would say the vinegar plane is more uniformly clean.

So in conclusion I'm a little in two minds here, the vinegar method does work, but it has a couple of drawbacks:
1) Finding a large enough tray/container to soak the rusty item in (not always a problem, but will be in many cases)
2) The item has to soak for a bit.
3) It seems to remove the finishing from some metal parts, so I guess you will have to be careful on what exactly you use it on.
4) You still have to brush the item, so some elbow grease involved.
5) You still have to sand a bit and apply machine oil of some sort to protect the metal.

This may be a good method for heavily rusted items or items that prohibit sanding down (lots of small details etc.), but for simple items I think just sanding down with a fine water paper and machine oil is quicker and just as effective.

I hope someone finds this useful, thanks for looking!
Commander
Sapling
 
Posts: 471
Joined: 29 Apr 2015, 15:11
Location: Pretoria, RSA
Name: Erich

Re: Table Saw

Postby Phil » 31 Jan 2017, 07:02

Erich

Nice job. Plane looks good.

Is the tool-in-a-can similar to Q20?

Did you have a look at what Wallace does on his machine refurbishment? (cleaning, polishing etc.) as a different approach to vinegar?
We don't stop woodworking because we grow old, we grow old because we stop woodworking!

https://www.instagram.com/phil_pretoria/
User avatar
Phil
Old Oak
 
Posts: 3499
Joined: 23 Jul 2014, 05:11
Location: Southern Africa 0054
Name: Phil

Re: Table Saw

Postby Andyp » 31 Jan 2017, 07:18

Good job Erich. Can you get hold of some Camillia Oil, or similar, to wipe over and protect the planes now that they are all nice and shiny?
I do not think therefore I do not am.

cheers
Andy
User avatar
Andyp
Petrified Pine
 
Posts: 11716
Joined: 22 Jul 2014, 07:05
Location: 14860 Normandy, France
Name: Andy

Re: Table Saw

Postby Commander » 31 Jan 2017, 07:50

Thanks for the comments gents!

Phil, I'm a big fan of Wallace's work on the Wadkin machines, very impressive and I'm sure he could do a better job of it. I don'y have most of the specialised equipment he uses though. And I would say tool in-a-can is very similar to Q20, it also comes in a aerosol can and its intended function is the same, as I recall I bought it one day when I couldn't find normal Q20.

Andy, I think the tool in-a-can will perform the same function, I will however keep an eye on it to make sure it doesn't start to rust. How often do you re-apply the Camillia oil? I'm guessing the thin coating will wear off as the plane is in use?

Also, I haven't repainted the handle yet as I'm not to sure what to use, any ideas? (I sanded it down to bare wood as the varnish was ruined, I would want to seal it again before using it.)
Commander
Sapling
 
Posts: 471
Joined: 29 Apr 2015, 15:11
Location: Pretoria, RSA
Name: Erich

Re: Table Saw

Postby Andyp » 31 Jan 2017, 08:07

Commander wrote:Andy, I think the tool in-a-can will perform the same function, I will however keep an eye on it to make sure it doesn't start to rust. How often do you re-apply the Camillia oil? I'm guessing the thin coating will wear off as the plane is in use?A


The stuff I have comes in a little spay bottle. A quick spray and a wipe, and (expect much mirth from the back) I then put them into socks before they go in the tool cabinet drawer.
I do not think therefore I do not am.

cheers
Andy
User avatar
Andyp
Petrified Pine
 
Posts: 11716
Joined: 22 Jul 2014, 07:05
Location: 14860 Normandy, France
Name: Andy

Re: Table Saw

Postby TrimTheKing » 31 Jan 2017, 08:44

I have started using Boeshield. Not cheap but dries like a hard wax/PTFE style surface sealing the metal for ages and only comes off on the planing surface so rarely needs topping up.

I suffer from terminal and potent rustfinger so I need to protect any and all of my Iron based tools from my corrosive digits and have tried camelia, wd40, veg oil and many more and found that Boeshield is far and away the best product, but at a price.

I bought it on a 2-for-1 from Rutlands last time I think which made it much more acceptably priced.

Cheers
Mark
Cheers
Mark
TrimTheKing
Site Admin
 
Posts: 7564
Joined: 16 Jun 2014, 13:27
Location: Grappenhall, Cheshire
Name: Mark

Re: Table Saw

Postby DaveL » 31 Jan 2017, 09:09

I prefer not to paint or varnish the handles, I use an oil finish. I like the Chestnut hard wax oil, but don't know if you can get it over there, I have used Danish oil or Finishing oil they work OK but are not as hard wearing.
Go job on removing the rust, I use Lubricating wax on my hand tools as well as on machines, stop rust and helps them slide.
Regards,
Dave
My tool kit is almost complete, only a few more to get.
User avatar
DaveL
Old Oak
 
Posts: 1917
Joined: 21 Jul 2014, 21:07
Location: Sudbury, Suffolk
Name: Dave

Re: Table Saw

Postby Commander » 31 Jan 2017, 09:50

Thanks for the tips! I think a lubricating wax would be great as it has the dual functions. I will have to do a bit of searching for some of the names and items mentioned.
Commander
Sapling
 
Posts: 471
Joined: 29 Apr 2015, 15:11
Location: Pretoria, RSA
Name: Erich

Re: Table Saw

Postby Malc2098 » 31 Jan 2017, 11:57

Thanks, Erich.

Notes taken for when I have to do mine, and I'll do a before and after post, too.
Malcolm
User avatar
Malc2098
Sequoia
 
Posts: 7207
Joined: 03 Jul 2016, 11:10
Location: Tiverton
Name: Malcolm

Re: Table Saw

Postby TomTrees » 01 Feb 2017, 00:21

I was going to suggest that you needed a plane otherwise you could never get the best out of the saw ...and that it was plain dangerous ....Good to see you've got some ..and a very nice job you've made of them too !
Now your gonna get precision ..the plane is the ultimate tool for accuracy and if ya use the plane as well as ya clean em up, theirs no going back now ...
What sort of bench do you have ?
User avatar
TomTrees
New Shoots
 
Posts: 156
Joined: 19 Aug 2014, 23:51
Name:

Re: Table Saw

Postby Commander » 01 Feb 2017, 07:47

Malc2098 wrote:Thanks, Erich.

Notes taken for when I have to do mine, and I'll do a before and after post, too.


I'm looking forward to it Malcolm!
Commander
Sapling
 
Posts: 471
Joined: 29 Apr 2015, 15:11
Location: Pretoria, RSA
Name: Erich

Previous

Return to Machines & Power Toolery

Who is online

Users browsing this forum: No registered users and 12 guests