It is currently 28 Mar 2024, 13:37

Oak settle: minor alterations(finished).

This forum is for any general questions, queries or plain old chinwaggery on Woody stuff in general.

Oak settle: minor alterations(finished).

Postby Mike G » 21 May 2020, 19:56

Goodness knows how many years ago, maybe 15 or 20, I made a couple of oak settles. I even posted about it on a forum somewhere, and one or two of you have been around long enough to perhaps have seen them back then. One of them has had a really tough life, having been parked in front of the underfloor heating manifold at my last house for all of its life until we moved house. Being in the kitchen, it has also been mopped at the bottom repeatedly:

Image

Image

Image

As you can see, it has really suffered. Time to give it a bit of TLC, I thought, so I popped it out to the workshop. No mean feat as it is solid oak throughout and weighs a ton. I needed a sack barrow for the task.

It's quite nice inside, and features an absolute rarity....some turning of mine:

Image

I popped the bottom out:

Image

Image

Then made some minor adjustments to the sides:

Image

Image

This was rather unfortunate. A loose panel that wasn't as loose as it should have been:

Image

I've discovered that I used PU adhesive in building this, so maybe it foamed up and went somewhere it shouldn't have done. No problem. A bit of filler and polish will soon hide the problem. The settle is going to a new home in the porch, so I want it looking spick and span for its new location.
Last edited by Mike G on 27 May 2020, 17:18, edited 2 times in total.
User avatar
Mike G
Sequoia
 
Posts: 9833
Joined: 30 Jul 2014, 22:36
Location: Suffolk
Name:

Re: Oak settle: minor alterations.

Postby kirkpoore1 » 21 May 2020, 21:17

Mike you have a gift for drama. :)

If only you'd have used hide glue--then you would have had to repair it years ago. :lol:

Kirk
User avatar
kirkpoore1
Old Oak
 
Posts: 1043
Joined: 21 Jul 2014, 22:12
Location: O'Fallon, Illinois
Name: Kirk

Re: Oak settle: minor alterations.

Postby DaveL » 21 May 2020, 21:19

I am sure you must have a good reason for sawing it in half, but it does seem a bit unkind!
Regards,
Dave
My tool kit is almost complete, only a few more to get.
User avatar
DaveL
Old Oak
 
Posts: 1917
Joined: 21 Jul 2014, 21:07
Location: Sudbury, Suffolk
Name: Dave

Re: Oak settle: minor alterations.

Postby Pinch » 22 May 2020, 07:44

I remember these very well. You posted them on here when I was making Andy's settle about 3 years ago. I like them a lot and they look beautifully made. I can imagine the weight of them. 8-)

I have every faith in what you're doing is the correct decision. :P
In my previous life, I was a tree.
User avatar
Pinch
Old Oak
 
Posts: 2808
Joined: 22 Jul 2014, 21:59
Location: Shropshire.
Name: Paul

Re: Oak settle: minor alterations.

Postby Andyp » 22 May 2020, 07:55

I hope you have a cunning plan :)
I do not think therefore I do not am.

cheers
Andy
User avatar
Andyp
Petrified Pine
 
Posts: 11716
Joined: 22 Jul 2014, 07:05
Location: 14860 Normandy, France
Name: Andy

Re: Oak settle: minor alterations.

Postby MattS » 22 May 2020, 08:54

:shock: :shock: :shock:

Sure a bit of polish would have fixed it - no need to saw in half!! :D Keen to see what you have planned!
MattS
Nordic Pine
 
Posts: 771
Joined: 04 Jul 2016, 10:05
Location: In the Weald of Kent
Name:

Re: Oak settle: minor alterations.

Postby Mike G » 22 May 2020, 11:28

Pinch wrote:.........I have every faith in what you're doing is the correct decision. :P


My wife has just seen it. She isn't quite so confident as you! :)
User avatar
Mike G
Sequoia
 
Posts: 9833
Joined: 30 Jul 2014, 22:36
Location: Suffolk
Name:

Re: Oak settle: minor alterations.

Postby TrimTheKing » 22 May 2020, 11:28

I'm guessing if it's going in the porch then it needs to be a bit shallower...
Cheers
Mark
TrimTheKing
Site Admin
 
Posts: 7560
Joined: 16 Jun 2014, 13:27
Location: Grappenhall, Cheshire
Name: Mark

Re: Oak settle: minor alterations.

Postby RogerS » 22 May 2020, 18:39

Mike G wrote:
Pinch wrote:.........I have every faith in what you're doing is the correct decision. :P


My wife has just seen it. She isn't quite so confident as you! :)


I've got one like that. They don't seem sympathetic when the time comes. But we like 'em that way, don't we !

Still think taking a saw to it was cruel.
If opportunity doesn't knock, build a door.
User avatar
RogerS
Petrified Pine
 
Posts: 13286
Joined: 21 Jul 2014, 21:07
Location: Nearly finished. OK OK...call me Pinocchio.
Name:

Re: Oak settle: minor alterations.

Postby Mike G » 22 May 2020, 20:26

I decided I didn't need the lower panels in the front, so I made a minor intervention with a jig saw:

Image

Removing the remnants from the edge grooves wasn't entirely without collateral damage:

Image

Here's one of the tenons cut off flush:

Image

A few minutes work with some chisels restored the mortise to its former glory, and revealed that I used to use machinery rather more than I do today:

Image

Here is the arm rest mortise after removing the tenon:

Image

My wife made me stop at this point. I was going to cut out the cracks in the back panels and put in 2 Dutchmen, then carve a Tudor rose in the middle of each panel. She thought I was joking:

Image

I had really hoped to avoid this next problem. Raising a panel in situ is just such a silly idea:

Image

Image

Image

Image

Image

Moving on to the tenons, I marked and cut the shoulders (knife then saw):

Image

Image

Workholding was something of a trial. Not your classic set up, and it made an awkward job even more awkward:

Image

I didn't get long at this today, so that's all I managed I'm afraid. I did however buy a whole load of wood, so more exciting woodworking adventures will ensue.
User avatar
Mike G
Sequoia
 
Posts: 9833
Joined: 30 Jul 2014, 22:36
Location: Suffolk
Name:

Re: Oak settle: minor alterations(finished).

Postby Mike G » 27 May 2020, 17:18

The next phase of the works involved putting the two halves of the settle back together again. This was quite awkward, and after a bit of thought I made a quick template of the back legs to ease proceedings:

Image

When offered up to the side panels I could now mark out the shoulder lines:

Image

However, because the arm rest was in a different plane from the side panel, the mark I made for that was a best guess, and not to be relied upon:

Image

What I did was cut the bottom two tenons accurately as per the template, but make the shoulder of the armrest 3 or 4mm on the safe side of the marked line. Then, it was a case of continual offering-up-and-adjusting. Sometimes those seekers of perfection miss out on the pragmatic solution, and this was a good example of guessing and adjusting. Poor old Steve Maskery has just fallen over in the corner in a heap, covered in a cold sweat . :) Anyway, sneaking up on the final shoulder line, and adjusting the panels etc in the process, took maybe 3 hours:

Image

Image

Image

Image

Image

But finally, everything lined up properly, the joints fitted well, the panels slid into their grooves, and all was well with the world:

Image

Image

Whilst the glue on that was drying I adjusted and put back the little overhang, the fixed part of the top:

Image

This photo, showing the seat offered up in its position, shows you how much width I had removed (and also how much colour I had stripped out of the thing by scraping off the oil and wax mess:

Image

So I hacked a piece off the front of the seat to make it fit its new circumstances:

Image

All the grooves around the front frame which had previously taken panels needed infilling:

Image

Those bored of dovetails might want to look away now.

The whole idea of this alteration to the settle was to convert it from being a box to being a shoe rack, with a couple of big drawers. So, time to make some drawers:

Image

But what's this, Mike? Why would you suddenly swap from dovetails to box joints?

Image

Patience, grasshopper.......First, I need to cut a couple of short grooves in here:

Image

The chisels fitted, but the mallet didn't. The router fitted, but the dust extraction didn't. Oh well, who needs functioning lungs anyway?

Image

Having previously made the draw sides and back, time to fit the fronts:

Image

Image

I put a little cut across the middle of each one, and chamfered it, to give the appearance of having 4 drawers rather than two:

Image

Image

Now, the answer to the box joint question. I really wanted to have the deepest possible drawers (front-to-back) that I could. These drawers are going to run on proprietry runners, so the face of the drawer has to overhang the sides by the thickness of the runner. Normally this is achieved by making a drawer box and planting on a drawer front, but, as I said, I needed the maximum possible front-to-back measurement. Thus the sides needed to join directly into the back of the drawer front, and for a novel problem I devised a novel variation of a joint:

Image

Image

Image

The floor of each drawer is long (about a metre) and although narrow I felt there was a good chance of them starting to sag over time. I therefore decided to strengthen the floor with some muntins:

Image

Image

All glued up:

Image

Whilst the drawers were drying, I did a little experiment with some dye to see if I could match the new into the old:

Image

After cleaning up the drawers:

Image

Image

....I messed about for quite a while making them fit properly:

Image

The final construction task was to re-build the floor, but above the drawers rather than below them. This involved a new piece on the back of the box, and these grooved end-pieces:

Image

Image

The front of those cross-pieces sits in the groove I struggled to rout out way back up there ^^^ somewhere. Here's a trial fit of the flooring. Note the half lap joint:

Image

Image

There is no possible means of clamping, so I found some heavy stuff for the glue up:

Image

I abandoned the idea of dying the new to match the old. The previous finish was oil, so I was pretty much stuck with re-oiling (unless I stripped right back to bare wood), so I tossed a coin between Osmo and Danish, and went with the latter. This was going to yellow fairly rapidly anyway, and the settle is going in quite a light space, so will also darken again fairly soon. Therefore, I reasoned, even if the match isn't great now in 6 months time no-one will be able to tell new from old:

Image

Image

Image

The area under the seat is a throw-in space for dog leads, gloves, balls, whistles etc (you know......dog-walking necessities).

After finally (yeah, yeah, I know it's been 3 or 4 years. I've been busy) sealing the porch floor, I wheeled the settle around and plonked it in position:

Image

Image

Image

Image

Here, for comparison, is what it looked like before I started work:

Image

It all fits rather well. I'm rather pleased with the settle 2.0. unfortunately, we had originally planned that it would be on the other side of the porch, and so I had installed these coat pegs accordingly. Since we changed our minds on the settle location, they're now on the wrong side of the room. How on earth am I going to get them out, whole, for re-location to the other side? They're friction fitted......but there's lots of friction:

Image
User avatar
Mike G
Sequoia
 
Posts: 9833
Joined: 30 Jul 2014, 22:36
Location: Suffolk
Name:

Re: Oak settle: minor alterations(finished).

Postby DaveL » 27 May 2020, 17:38

If you find the drawing for the pegs and a few off cuts of oak I could turn some more for you. So you could just leave the current ones there, or trim them off flush.
I could have a look on my PC, the drawing might still be there somewhere.
Regards,
Dave
My tool kit is almost complete, only a few more to get.
User avatar
DaveL
Old Oak
 
Posts: 1917
Joined: 21 Jul 2014, 21:07
Location: Sudbury, Suffolk
Name: Dave

Re: Oak settle: minor alterations(finished).

Postby Malc2098 » 27 May 2020, 17:45

Nice.
Malcolm
User avatar
Malc2098
Sequoia
 
Posts: 7207
Joined: 03 Jul 2016, 11:10
Location: Tiverton
Name: Malcolm

Re: Oak settle: minor alterations(finished).

Postby Mike G » 27 May 2020, 17:47

Very kind of you Dave. It might well come to that......but I'm going to have a try at hauling the old ones out tomorrow. I'll let you know. As for finding the drawing...!!! Miracles happen, I guess. I do have one or two of your pegs surplus, which would probably be easier for you to work from anyway, wouldn't it?
User avatar
Mike G
Sequoia
 
Posts: 9833
Joined: 30 Jul 2014, 22:36
Location: Suffolk
Name:

Re: Oak settle: minor alterations(finished).

Postby Andyp » 27 May 2020, 18:05

Great job. I can barely see the join from here.

You certainly can't leave those pegs there, at head height for someone.
I do not think therefore I do not am.

cheers
Andy
User avatar
Andyp
Petrified Pine
 
Posts: 11716
Joined: 22 Jul 2014, 07:05
Location: 14860 Normandy, France
Name: Andy

Re: Oak settle: minor alterations(finished).

Postby Phil » 27 May 2020, 18:07

:text-goodpost:


Nice job Mike. :eusa-clap:
We don't stop woodworking because we grow old, we grow old because we stop woodworking!

https://www.instagram.com/phil_pretoria/
User avatar
Phil
Old Oak
 
Posts: 3499
Joined: 23 Jul 2014, 05:11
Location: Southern Africa 0054
Name: Phil

Re: Oak settle: minor alterations(finished).

Postby Woodbloke » 27 May 2020, 18:07

Great conversion Mike, please don't take offence but I reckon you could have chosen those drawer pulls a little more sympathetically...far too plain and conservative. IMO something a little more 'ye oldie worldie, Olde England' blah blah etc might be more in keeping.
I've said it before plenty of times, but handles/pulls are THE most important part of any project. Just my two Euros (for what they're worth and it's not much :D) and repeat, no offence intended - Rob >> ducking for cover :D
I no longer work for Axminster Tools & Machinery.
User avatar
Woodbloke
Sequoia
 
Posts: 5866
Joined: 22 Jul 2014, 10:06
Location: Salisbury, UK
Name:

Re: Oak settle: minor alterations(finished).

Postby Mike G » 27 May 2020, 18:16

They're a place holder, Rod, whilst we look for something more appropriate. Actually, whilst we try to agree what would be more appropriate..... :lol:
User avatar
Mike G
Sequoia
 
Posts: 9833
Joined: 30 Jul 2014, 22:36
Location: Suffolk
Name:

Re: Oak settle: minor alterations(finished).

Postby DaveL » 27 May 2020, 19:31

Yes I should be able turn more from a pattern peg.
What diameter are they? I might have a collet that could grip them to give a better chance of removing the current ones.
Regards,
Dave
My tool kit is almost complete, only a few more to get.
User avatar
DaveL
Old Oak
 
Posts: 1917
Joined: 21 Jul 2014, 21:07
Location: Sudbury, Suffolk
Name: Dave

Re: Oak settle: minor alterations(finished).

Postby Mike G » 27 May 2020, 19:46

I'm making a wooden collet tomorrow, Dave. If that doesn't work I'll let you know, but I have a plan coming together.
User avatar
Mike G
Sequoia
 
Posts: 9833
Joined: 30 Jul 2014, 22:36
Location: Suffolk
Name:

Re: Oak settle: minor alterations(finished).

Postby DaveL » 27 May 2020, 20:00

I have just had a thought as to why they are held so firmly, the pegs where dry i.e. seasoned while the beam you fitted them into was still relatively green. So the holes have shrunk as the beam has dried. That's a technique used in chair making to stop the spindles becoming loose in the legs. I am not sure you will get the out whole!
Regards,
Dave
My tool kit is almost complete, only a few more to get.
User avatar
DaveL
Old Oak
 
Posts: 1917
Joined: 21 Jul 2014, 21:07
Location: Sudbury, Suffolk
Name: Dave

Re: Oak settle: minor alterations(finished).

Postby Mike G » 27 May 2020, 20:25

DaveL wrote:......I am not sure you will get them out whole!


Neither am I!
User avatar
Mike G
Sequoia
 
Posts: 9833
Joined: 30 Jul 2014, 22:36
Location: Suffolk
Name:

Re: Oak settle: minor alterations(finished).

Postby MJ80 » 27 May 2020, 20:54

That Mike is utterly brilliant
MJ80
Sapling
 
Posts: 323
Joined: 13 Sep 2016, 19:21
Name:

Re: Oak settle: minor alterations(finished).

Postby RogerS » 27 May 2020, 21:20

:eusa-clap: :eusa-clap: That's a real tour-de-force, Mike.
If opportunity doesn't knock, build a door.
User avatar
RogerS
Petrified Pine
 
Posts: 13286
Joined: 21 Jul 2014, 21:07
Location: Nearly finished. OK OK...call me Pinocchio.
Name:

Re: Oak settle: minor alterations(finished).

Postby Mike G » 27 May 2020, 21:35

Thanks guys.
User avatar
Mike G
Sequoia
 
Posts: 9833
Joined: 30 Jul 2014, 22:36
Location: Suffolk
Name:

Next

Return to General Woodworking

Who is online

Users browsing this forum: No registered users and 11 guests